ShirazOnline
صفحه 2 از 2 نخستنخست 12
نمایش نتایج: از شماره 11 تا 13 , از مجموع 13

موضوع: برسی و آموزش منطقه فرنل Fresnel Zone ونکته هایی که باید در مورد آن بدانیم

  1. #11
    کاربر عادی nimadrayaneh آواتار ها
    تاریخ عضویت
    Sep 2012
    نوشته ها
    107
    تشکرها / پسندها

    پیش فرض

    Fresnel zone calculation


    A particularly common problem with radio systems is communication errors. The occurrence of communication errors changes significantly depending on the method of placement of the radio equipment. With radio communication, it is important to ensure "line of sight" between the transceivers.
    When we can see the receiving antenna we use the expression "line of sight" without much thought, but with radio waves, it can be said that "line of sight" is only achieved when the Fresnel zone indicated below is established.
    With radio systems used at about 1.5 m above ground, if a Fresnel zone is not established, multipath interference will occur, so that the true electric field intensity cannot be obtained. If operation of the equipment is unstable, it is necessary to consider whether the fixed station can be set up in a higher place.


    Radio system errors
    Radio system errors occur when the bit strings of 0's and 1's that make up the data cannot be identified by the electronic circuits inside the receiver, due to corruption of the transmission data.

    Viewed on a temporal basis, assessment of the receive data is performed in the middle position of the receive bit width, and in terms of level, the bit is determined to be 1 or 0 by whether the received voltage of the median value (threshold value) is bigger or smaller. This identified signal is the signal after FSK demodulation. Because the signal and noise are a composite waveform to begin with, if the difference between the signal level and noise level (inside the receiver) is low, with certain sampling timing, since the decision is made with a waveform in which the threshold value is exceeded due to noise, an error results. Therefore in general, the signal level is required to be about 20 dB (100 times the voltage ratio) greater than the level of noise.

    FSK radio equipment is immune to the influence of amplitude noise, but if there is an obstruction between the antennas (the ground, buildings, natural objects and so on), the radio waves will be reflected resulting in multipath interference. At the receiving point, the composite wave incorporating the delayed radio waves is distorted in amplitude, resulting in an error. In addition, the ratio of the noise component of signals that enter the demodulation circuit in a location with weak electric field intensity is high in relation to the signal, and this causes errors. Of course, signals generated by the antenna due to external noise will also have an impact on amplitude and frequency.

    Fresnel zone
    In order for radio waves emitted from the transmitter to reach the receiver without attenuation of power, a certain amount of space is required. The energy cannot reach the receiver via one straight line in space. It is easy to understand for example that the waves will not get there through a hole the size of a needle in a concrete wall.
    The space required is a spheroid with its center along the shortest distance between antennas, and this is called the Fresnel zone. In fact this space expands indefinitely, but the part that principally contributes to communicating the energy is called the 1st Fresnel zone.
    If there are obstacles inside the Fresnel zone, insufficient energy is transmitted so that received field intensity becomes weak. If the received field intensity is weak, the probability that errors will occur becomes gradually higher. The receive sensitivity of the receiver is absolute, and propagation loss which depends on the distance traveled by the radio waves cannot be avoided. Therefore in order to prevent errors from occurring, it is important to ensure that the received radio waves are as close as possible to the theoretical value.

    The 1st Fresnel zone is a spheroid space formed within the trajectory of the path when the path difference when radio wave energy reaches the receiver by the shortest distance, and when it gets there by another route, is within λ/2. In this case, λ is the wave length of the radio wave (wave length = speed of light / frequency) which at 400 MHz is 0.75 m.

    When positioning radio systems
    The distance between the Fresnel zone boundary and a straight line running the shortest distance between the antennas is called the Fresnel radius, and if there are no obstacles in the space forming 60% of this distance, propagation characteristics are said to be the same as in free space. [فقط اعضا می توانند لینک ها را مشاهده کنند برای ثبت نام اینجا را کلیک کنید]

    [فقط اعضا می توانند لینک ها را مشاهده کنند برای ثبت نام اینجا را کلیک کنید]
    Fresnel zone formula



    Instructions



    1. Click the "Figure / Graph" button to display the calculation screen.
    2. Enter the required items in the yellow input fields for entering parameters. To calculate the Fresnel zone, after setting the parameters in the input fields, push the Enter key on your PC, or click the "Calculate" button.
    3. Set the distance d in the pink input field.
    4. To find the Fresnel radius, decide the position to find (distance on the X axis), and left-click with your mouse on the graph.

    * Right panel
    The values shown in the panel on the right are the Fresnel radius and diameter at the midpoint.

    ویرایش توسط nimadrayaneh : 2013/12/05 در ساعت 12:37 AM

  2. Thanks pooyesh, IliyaBlack, Netir thanked for this post
  3. # ADS
    Circuit advertisement
    تاریخ عضویت
    Always
    نوشته ها
    Many
     

  4. #12
    کاربر ممتاز حرفه ای shiraz آواتار ها
    تاریخ عضویت
    Apr 2007
    نوشته ها
    2,481
    تشکرها / پسندها

    پیش فرض

    اینم یک امورش خوب
    [فقط اعضا می توانند لینک ها را مشاهده کنند برای ثبت نام اینجا را کلیک کنید]

  5. Thanks pooyesh, admin, IliyaBlack, gorgan_best_boy thanked for this post
  6. #13
    کاربر عادی meisamphp آواتار ها
    تاریخ عضویت
    Apr 2010
    نوشته ها
    179
    تشکرها / پسندها

    پیش فرض

    سلام .
    يه سئوال از كارشناسان محترم دارم ، من خيلي جاها در مورد فرنل زون خوندم . اما يه موضوع مهم واسم پيش اومده ،

    تا اون جايي كه من ميدونم هرچي گين آنتن بيشتر باشه تمركز امواج آنتن بيشتر ميشه پس در نتيجه شعاع فضاي فرنل بايد باريكتر بشه ، سئوال من اينه كه چرا هيچ جايي توي محاسبات ناحيه فرنل از گين آنتن صحبت نشده ؟؟؟ در صورتي كه وقتي گين آنتن بالا باشه تمركز امواج بيشتر و شعاع ناحيه فرنل كمتر بايد باشه ..


    ممنون ميشم جوابم روبدين ..

    ياعلى ..

صفحه 2 از 2 نخستنخست 12

اطلاعات موضوع

کاربرانی که در حال مشاهده این موضوع هستند

در حال حاضر 1 کاربر در حال مشاهده این موضوع است. (0 کاربران و 1 مهمان ها)

موضوعات مشابه

  1. تفاوت Stub Zone و یک Secondary Zone
    توسط sadegh.nakhjavani در انجمن مایکروسافت(Microsoft)
    پاسخ ها: 3
    آخرين نوشته: 2012/04/02, 10:09 PM
  2. پاسخ ها: 0
    آخرين نوشته: 2011/08/30, 03:37 PM
  3. stub zone
    توسط a_f در انجمن مایکروسافت(Microsoft)
    پاسخ ها: 1
    آخرين نوشته: 2011/03/08, 02:59 PM
  4. چطوري باگ DNS zone transfer رو پچ كنيم ؟
    توسط dezchilds در انجمن مدیریت وب(WebManagement)
    پاسخ ها: 8
    آخرين نوشته: 2011/01/13, 02:41 PM
  5. فیلم آموزشی : Stub zone
    توسط llvllr.zel2o در انجمن مایکروسافت(Microsoft)
    پاسخ ها: 0
    آخرين نوشته: 2009/01/29, 02:17 AM

علاقه مندی ها (Bookmarks)

علاقه مندی ها (Bookmarks)

مجوز های ارسال و ویرایش

  • شما نمیتوانید موضوع جدیدی ارسال کنید
  • شما امکان ارسال پاسخ را ندارید
  • شما نمیتوانید فایل پیوست کنید.
  • شما نمیتوانید پست های خود را ویرایش کنید
  •